# Requirements register “Published” means supported by the cited guidance. “Derived” is an engineering consequence. Local recommendations and objectives require an organisation's own approval. These are proposed design requirements, not a new NHS standard. The supplied requirement RA-10 was incomplete. Its wording below is an explicitly local completion. Later identifiers are additions from this research. | ID | Proposed requirement | Basis | Source | Acceptance evidence | |---|---|---|---|---| | RA-01 | Use CIM with the appropriate RA role for each operation. | Published | [SRC-011](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-011) | Authorised operator completes the selected workflow. | | RA-02 | Use the current supported Smartcard Connect package and card middleware. | Published | [SRC-005](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-005) | Installed package and service state recorded. | | RA-03 | Provide primary and secondary readers for the reference RA setup. | Published | [SRC-002](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-002) | Both interfaces identified and usable. | | RA-04 | Use the supported DoH 300 (V2) for physical printing. | Published | [SRC-003](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-003) | Model, serial and printed result recorded. | | RA-05 | Validate the integrated printer reader independently. | Derived | [SRC-003](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-003) | Correct device/driver and personalisation result recorded. | | RA-06 | Support the required Series 10 management operations. | Published | [SRC-004](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-004) | Each intended operation tested on Series 10. | | RA-07 | Allow required service domains through the chosen network path. | Published | [SRC-006](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-006) | Actual gateway and service access recorded. | | RA-08 | Demonstrate the full workflow without HSCN where this is a design objective. | Local objective | [SRC-006](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-006) | Successful end-to-end test with no HSCN route. | | RA-09 | Align client software with the current WES and vendor support. | Published | [SRC-007](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-007) | Version inventory compared with current support state. | | RA-10 | Control installation, updating and rollback of device drivers. | Local recommendation | [SRC-013](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-013) | Owner, approved package and rollback evidence recorded. | | RA-11 | Validate browser cookies and Local Network Access settings. | Published | [SRC-010](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-010) | Managed browser policy and local integration tested. | | RA-12 | Validate the full remote session when virtualisation is used. | Derived | [SRC-005](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-005) | Isolation, redirection and recovery tests pass. | | RA-13 | Provide PIV middleware at both ends of a remote PIV-card setup. | Published | [SRC-008](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-008) | Local and remote installations verified. | | RA-14 | Record acceptance evidence before operational approval. | Local recommendation | [SRC-001](https://nhs-smartcard-printing-wiki.pages.dev/sources/index.md#src-001) | RA service owner signs the acceptance record. | Use the [acceptance checklist](https://nhs-smartcard-printing-wiki.pages.dev/acceptance/index.md), [evidence matrix](https://nhs-smartcard-printing-wiki.pages.dev/evidence-matrix/index.md) and [validation queue](https://nhs-smartcard-printing-wiki.pages.dev/validation-queue/index.md) together. Passing a documentation review does not satisfy a physical acceptance test.